UA-144211750-1

How to Change Water Filter In Whirlpool French Door Refrigerator [Easy Guide]

If you notice that the water in your refrigerator is murky, it is possible that your water filter needs to be replaced.

It’s possible that your water filter has been working so hard that it has to be replaced.

Water filter replacement on your refrigerator is not rocket science; you can do it yourself and seem like an expert.

Continue reading to learn the quickest and most straightforward methods for replacing Water Filter in your Whirlpool French Door refrigerator.

Never forget that you should change your water filter every six months and that you should always refer to your use and maintenance instructions!

How To Change Water Filter In Whirlpool French Door Refrigerator
How to Change Water Filter In Whirlpool French Door Refrigerator

Replace the water filter on your system.

Such convenient features come with the additional duty of checking the water filter on a regular basis to ensure that it is functioning correctly.

It is necessary to change the filters every 6 months in order to ensure that there is no obstruction in the water flow.

People often inquire about the best methods for changing water filters, so if you are one of them, read on to find out the answers to your concerns regarding water filter switching.

The following are some reasons why you may need to change your water filter:

  • There is no water being dispensed.
  • Ice is not being produced by the ice machine.
  • The ice maker only produces a little amount of ice.
  • The touchpad does not react when there is leaking or noise.

Find the Location of the Water Filter

The water filter cover may be found in the top right-hand corner of the refrigerator’s interior on the shelf.

A push or a pull release will be used on the filter covers, depending on the design of the cover.

The push style can be distinguished by the word push embossed on the tab on the cover end that is facing out, whereas the pull-type will have an open invoice on the front underside of the cover, which can be distinguished by the absence of the word push on the tab.

When using the push type filter cover, release the body by pressing in on the tab and slightly downward, so that the filter cover hangs open at an angle from the rear.

For the pull-style filter cover, release the body by gently pushing the tab toward the front, allowing the filter cover to hang open at an angle from the rear.

The blue bypass cap will be located within the filter aperture of the refrigerator if this is a fresh installation.

Removing the blue bypass cap is as simple as twisting it counterclockwise, about one-quarter turn, and then pulling it out straight.

Keep the bypass cap in case you need it in the future.

Select the Most Appropriate Option

First and foremost, we would like to remind you that Whirlpool refrigerators are equipped with a variety of water filters that are compatible with all of the models manufactured by the company.

We recommend that you visit the official website in order to choose the product that best fits your requirements. Take a look at some of the best aftermarket refrigerator water filters available.

Recommended:  What Is the Power Consumption of a Mini-Fridge? [The Truth Revealed!!]

Instructions on how to use each filter

For new users, replacing the filter may be a difficult task.

Furthermore, the many kinds of filters that are accessible are a contributing factor to the complexity.

The instructions provided here are for a variety of different kinds of filters that you may encounter.

Filter No. 1

everydrop® Refrigerator Water Filter 1 - EDR1RXD1 (Pack of 1)

Step one: Double-check that you’re using the proper filter.

Step number two:

  • Remove the new filter from its box and set it aside.
  • Remove the purple cap from the top of the filter and set it aside.
  • Check to see that the black O-rings are still in their original positions.

Step Three: Look in your refrigerator for your water filter.

Filter One may be found on the inside of the ceiling, in the top right-hand corner, or in the base grille, depending on where you are.

Step Four: Open the filter cover door by pulling it open. With each opening of the door, the filter will be freed and expel a little amount of material from the housing.

Pull the filter straight out of the door after it has been fully opened.

Step Five: It’s important to note that extra water may leak from the old filter, so keep a towel nearby.)

Step Five: It’s time to put your new Every Drop filter in place. Hold the filter in such a way that the arrow at the end of the cartridge is properly aligned with the filter.

Using the new filter, carefully slide it into the hole until it is aligned with the old filter’s aperture.

Step Seven: firmly press down on the filter cover door until it snaps shut completely.

Step Eight: Before consuming, run four liters of water through your refrigerator’s water dispenser to eliminate any air bubbles and guarantee that Every Drop’s rapid flow performance is maintained.

Water with a better taste may be obtained by following these steps.

Filter No. 2

To begin, you must first find the filter, which is located in the top right corner of the refrigerator.

Pull the door down and the filter down so that it is sloping toward the bottom.

Once it is completed, twist the filter counter-clockwise and remove it.

After that, take the replacement filter out of the package and unscrew the cap.

The new filter should be placed in such a manner that the arrow pointing upwards is visible.

Once everything is in place, spin the filter counter-clockwise and shut the lid.

Now, run 3 liters of water through the filter to ensure that it is functioning correctly.

Filter No. 3

Step One: Make sure you have the proper filter number and color cap for your refrigerator by following these steps.

Step Two: is to take off your hat and recycle it.

Step Three: is to locate your holder. It will be located towards the bottom of your refrigerator.

 Step Four: is to pop out the old one (have a towel nearby in case there is any extra water, which is perfectly normal).

Step five: reattach the bottom cap on the new one and slip it into place as instructed. You’ll be able to hear it click.

Step Six: After it has been completely secured in place, turn on your dispenser to activate it.

***It’s possible that you’ll hear a strong air pressure sound, but this is normal.

It’s as simple as that to have six months of clean, fresh-tasting water and ice delivered to your door.

Filter No. 4

Step one: Double-check that you’re using the proper filter. If you need assistance determining if Filter Four is appropriate for your refrigerator, visit everydropwater.com and utilize the filter finder.

Step two: is to take your new filter out of its box and set it aside.

Remove the cartridge’s seal by pulling it away from the end of the cartridge.

Step Three: Look in your refrigerator for your water filter.

Filter Four may be found on the interior of the room, at the top right-hand corner of the ceiling.

Recommended:  How Much Does a Refrigerator Weigh? [ Your Answer Here!]

Replace a used filter by unscrewing it and pulling it straight out.

Step Four: To do so, spin the cartridge counterclockwise until it releases and then pulls straight out.

It’s important to note that extra water may leak from the old filter, so keep a towel nearby.

Step Five: Install your new Every Drop filter  

Step Six: align the filter with the refrigerator’s opening and push it in until it is securely in place.

Step Seven: Rotate the filter counter-clockwise until it comes to a complete halt. Close the filter cover with a squeegee.

Step Eight: Before drinking, run four gallons of water through your refrigerator’s water dispenser to clear it out.

Cleaning and replacing the water and ice filter in a Whirlpool side by side fridge

Following the replacement of the filter, you will need to discharge at least 4 gallons of water to flush out the carbon in the filter as well as any air before using the unit again.

According to the manufacturer’s recommendations, this filter should be replaced about every six months.

The refrigerator will emit a bell and display a warning on the screen.

Also compatible with other manufacturers such as Maytag, Whirlpool, Amana, Jenn-Air, and other similar models of appliances.

Maintaining Your Refrigerator’s Condenser Coils Will Keep It Safe.

A clogged condenser coil may cause a refrigerator to operate hotter and possibly decrease its lifetime if it is not cleaned regularly.

As a result, it is essential to regularly clean your refrigerator’s condenser coils in order to avoid blockage from debris, dust, and pet fur.

Some types do not need cleaning, while others can be cleaned by the owner with relative ease, and still, others require the services of a trained specialist.

**Before trying to clean the coils, please refer to the use and care handbook for instructions.

If they get blocked, they are unable to effectively discharge heat, causing your refrigerator to run hotter or forcing your compressor to consume more energy to compensate.

Both of these factors may reduce the lifetime of your refrigerator.

What is the best way to clean the condenser coil on a Whirlpool refrigerator?

Step 1: Vacuuming and gentle brushing the condenser coils are the best method of cleaning them.

To clean the condenser coils, unplug your refrigerator or turn off the electricity to the appliance.

Step 2: Remove the base grille from the bottom of the refrigerator in the second step.

To clean the grill, the open regions behind the grille, and the front surface area, use a vacuum cleaner and a soft brush to clean the surface area.

Step 3: Reinstall the base grille and plug in the refrigerator or re-establish electricity to the appliance.

In the case of a very oily or dusty environment, or if there is a lot of pet traffic, the condenser may need to be cleaned every two to three months.

Follow the directions in the use and care guide, or contact the Customer Experience Center, if you have any questions at this point.

Is It Possible to Bypass the Water Filter?

Even if it is very simple to change your water filter, there may come a moment when it is necessary to do so and you are unable or unable to do so for various reasons.

It’s possible that your house has its own filtering system, or that you just don’t want to bother with changing the filter.

While it is generally recommended that you change the filter, there is no reason why you cannot bypass it if you want.

Whatever your motivation, here’s how to get around the water filtering system on your Whirlpool refrigerator.

Step 1: Identify and locate the Filter

The first step is to locate the appropriate filter.

It has already been stated that you may find the filter in one of two places: behind the grille at either end of your refrigerator’s bottom or in the rear corner of the door.

Everything is dependent on your particular model.

Recommended:  How Does a Propane Refrigerator Work [In-depth Guide]

If the filter is located in the bottom grille, it may be easily removed.

Simple: spin the circular filter cover counter-clockwise until the handle is upright in respect to the floor, then pull the filter cover outwards. If the filter is located within the refrigerator, there will be a release button that you will need to press before removing the filter from the fridge.

Step 2: Put the Dispenser to the Test

Following the removal of the water filter, you should examine the water dispenser.

This will just take a few minutes of your time to complete.

If the dispenser is operational and water continues to flow, your refrigerator is equipped with a built-in bypass, and you will not be required to take any more action.

In the event that the water supply stops working, a bypass plug will be needed.

While you wait for the aforementioned plug to arrive, reinstall the filter that you previously removed from the system.

Step 3: Disconnect the plug.

If the dispenser does not function after removing the filter, you will need to identify the exact make and model of your refrigerator in order to locate a bypass plug that will function.

The owner’s handbook may be found on the inside of the freezer door or just outside the refrigerator door if you don’t know where to look for it.

When you have all of the information you need, you may purchase the bypass plug that is compatible with your particular refrigerator model. You should be able to locate one on the internet for a reasonable price and in a short period of time.

Step 4: Installation of the Bypass Plug 

Now that you have the bypass plug in your possession, the only thing left to do is to remove the filter and replace it with the bypass plug.

This may be accomplished by inserting it into the same port on the interior of the refrigerator or, if it is in the base grill, by connecting it to the same valve on the outside of the refrigerator.

It’s important to check the dispenser for leaks once you’ve closed up any of the necessary doors or panels.

To determine whether there are any visible leaks, remove the bypass plug and reinstall it if needed.

You no longer have to be concerned about using your water dispenser device since it has a filter built into it.

Our Final Thoughts

Changing your refrigerator water filter is probably something you’ve never given much attention to, particularly since it’s tiny and hidden away in an inconspicuous location.

However, the family takes full use of it, filling up reusable water bottles, preparing favorite meals, and brewing tea and coffee, among other things.

However, in order to maintain your water and ice taste fresh and free of pollutants, it is necessary to replace it on a regular basis – we suggest changing it once every six months.

Frequently Ask Questions

Changing your refrigerator’s water filter every six months is a hassle, but is it really necessary?

It is recommended that you change your refrigerator filters every six months. You should not keep a filter in place for more than one year.

In general, the longer you use a carbon filter above its maximum capacity, the more hazardous your water is likely to become.

Which water filter is the most effective for drinking water?

Reverse osmosis filters are the gold standard for eliminating a significant proportion of pollutants from water, including potentially harmful waterborne germs.

They are also the most expensive. The filters function by applying pressure to the water as it passes through the reverse osmosis membrane.

What is the location of the refrigerator’s air filter?

The air filter is placed on the back wall of the refrigerator section, towards the top of the compartment.

About Khelly